L.E.D. Tail lights...on the cheap.

[longhorn man]

I'll see if I can't re-enact the process and document it all on digi-film. It was pretty simple, and my cost was just shy of 50 bucks, but i do get a discount from the shop. I figure it can be duplicated by anyone anywhere in the U.S. (and maybe up north too, depending on your local laws) for less than 70 bucks. These already have D.O.T. aproval and no one can say anything about them.
On a bad note, suburban and panel owners need not apply. I tried mocking this up on cheesewagon's rig and it wouldn't work. Sorry guys/galls. :(


They aren't as bright or as cool as the real conversion in one of the catalogs out there...but at this price, I think there may be more than a hand full of us running with L.E.D. tail lights here real soon.


Now I need to get my hands on step side tail lights to see if I can do the same for the step side crowd. ;)

Here is just the tail light.
http://www.digitalpose.com/mbr/1/8856/p/502770_3797856216812265826_vl.jpg

And a brake light.
http://www.digitalpose.com/mbr/1/8856/p/502771_6690121463079482632_vl.jpg

Now in stereo...(brake lights again)
http://www.digitalpose.com/mbr/1/8856/p/502769_7772099138887399649_vl.jpg

[longhorn man]

Well, some idiot (me) left my digi-cam in the rain last week and it has gotten very tempermental, and it did not want to work today. So I will try to explain it the best I can. If I can get the camera to work again soon, I will folow up with pictures (obviously it worked yesterday, so it may work again tomorow)

Here is the main part of the set up. For $25 each, (discounted a little) I bought 2 of these lights. Mine are a no name generic brand, and I am finding that this may make it hard to duplicate, but the light looks something like this. Napa should be able to get you something very similar.
http://www.truck-lite.com/tl/tl/catalog/images/grap/sttl/stt/stt07lr.jpg
Any U-haul place should be able to get one. The one I used had a hard plastic outer flange instead of the rubber grommet seen in this pic. The main thing was the lens. It was totally flat where most lights of this shape are kinda domed. (mod 60 is the shape/size) I had to cut off the flange, and when I did that, the light assembly fit right into the stock unmodified tail light lens. The edges of the lens held onto the LED perfectly. If it were a little loose, I would have used a dab of clear sillicone to hold it in place. DO NOT USE SUPER GLUE, it will discolor the lens.
Then, I removed the tail light bucket (or what ever they call the metal backing plate that has the actual light socket) It is held to the bed with 2 5/16 inch bolts. Once you have it unbolted, pull it out (with harness) untill it hangs down enough to access the entire tail light hole.
Cut the plug off of the harness.
If you were to place the LED lamp and tail lens assembly into the light hole on the bed, you'd see the lens is about 1/4 to 1/2 inch from setting where it belongs. I used a 5 pound hammer and a 1/2 inch drive, 10 inch extention (My drift is at the shop) and proceded to beating the offending sheet metal out of the way. (it didn't take very much) Make a few blows to the metal, and try to fit it in. No need in pummeling it more than needed.
Once it fits in the hole to your liking, use a long skinny punch, and reach through the two mounting holes of the lens to mark the inner sheetmetal for drilling. You'll need some screws about 2 - 3 inches long. (about 2 1/2...but I didn't actually measure) Drill the holes, and test fit the lens and LED lamp assembly. These screws will be used to hold the lens in place since the buckets or backing plate will not be re-used. With some carefull pounding, it should fit fine, and the pressure from the screws will hold the led lamp against the sheet metal. So even if it was a tad loose (Which mine was actualle a bit too tight) in the lens, the lamp will be 'sandwiched' inbetween the lens and the metal.
Now for the electrical. The wire colors on the LED may well look odd. Mine had a red, white, and black. Luckily, mine was also labeled. The white was ground, which I crimped an eyelet on there and used one of the original 5/16 inch bolts to ground it. Then the tail light wire goes to the brown wire from your stock harness, and then the brake/turn wire would go to the green/yellow wire (depending on which side of the truck you are working on) Use good crimp on connectors and heat shrink to keep the nasty crap out of your connection. I used the crimp ons that have head shrink on them already. They can be found at NAPA, but they are a little spendy.
Now re-install the LED/lens assembly, and test it out.
As for the blinker issues that some people have reported with LED lights, you may or may not have issues with this.
I got lucky. My truck's turn signals will blink even if there are no lights installed. I don't know why it does this, or even if I like it like that or not. But that's how mine works. (It should not work like that. The indicator should stay on, and the remaining light (with one removed or burned out) should lite and stay lit) I do have electronic flashers on mine, and that may have something to do with it, but I do not know.
I DO know that NAPA has a small LED blinker unit that can be purchased, and is supposed to cure the non-blinking singnals from the reduced load that the LED will put on the blinker.
Now do the other side and enjoy.


I'm not joking, the very first time I drove it with these lights in there, some one at an intersection yelled asking where I got the LED conversion for my truck. He was driving an old camaro, but said he had a truck at home he was restoring.
This put an even bigger grin on my face. :D